How To Change Battery In Jeep Key Fob?

Make that the negative side of the new CR2032 battery is facing down. Place the circuit board into the keypad, and then the keypad inside the key. Finally, clasp the two pieces of the key fob together.

Similarly, How do I open my Jeep key fob?

To open the Jeep key fob, use a flathead screwdriver. It should be inserted into the fob seam, which is adjacent to the keyring mount. To separate the key fob halves, gently press down on the screwdriver. Do not twist as you push down, since this may harm the plastic and cause the key fob to break.

Also, it is asked, What do I do if my key fob battery dies Jeep?

Close the key fob and replace the mechanical key inside. Push the START button with the key fob. Instead of pressing the button with your finger, push the key fob against it. Many manufacturers utilize this as a backup device to guarantee that the vehicle can start even if the fob is dead.

Secondly, How much is a key fob battery cost?

These batteries typically cost $10 or less, however some fobs need two. Because it simply takes a minute or two, battery specialist shops and dealers often replace the batteries for free.

Also, How do you change the battery in a 2017 Jeep Grand Cherokee key fob?

How to Replace the Key Fob Battery on a 2017 Jeep Grand Cherokee Step 1: Place the screwdriver near the key ring in the seam on the key fob. Step 2: Gently pry the two sides of the key fob apart with the screwdriver. Step 3: Make a mental note of the old battery’s polarity.

People also ask, What battery does a 2018 Jeep Grand Cherokee key fob take?

4 piece Duracell 2032 3V Lithium Coin Battery with Bitter Coating.

Related Questions and Answers

What kind of battery does a Jeep Grand Cherokee key fob take?

Place a fresh CR2032 battery in the positive side down position. Finally, snap the device’s two pieces back together. That’s all there is to it. Congratulations!

Will dead battery in key fob cause car not to start?

8. The battery in the key fob has died. If you have a car that you can start without taking the fob out of your pocket, the fob has a battery that communicates with your vehicle when you’re near enough. If the fob battery dies, your car will no longer recognize you and will refuse to start.

Can I start my car without the fob?

Simply said, if you lose the keyfob that allows you to start your automobile with a push-button start before you attempt to drive, you will be unable to do so.

Why does my key fob not work after replacing battery?

To open the key fob and inspect for damaged contacts or misaligned buttons, you may use basic tools. Replace the automobile key fob if that doesn’t work. Another reason your vehicle remote may not function after replacing the battery is the lock. Check for these symptoms to see whether the lock or vehicle door has become faulty.

Can I replace a key fob myself?

You may be able to program a replacement yourself, depending on the age and type of your automobile. The technique for programming a key fob manually varies: Owner’s manuals from certain automakers provide instructions. In many circumstances, information may be accessed on the internet.

Where can I go to get my key fob battery changed?

Your local AutoZone can provide you with a replacement key fob battery of whatever sort you need.

How do you open a key fob to change the battery?

Replace the battery in your car’s key fob in 5 easy steps. To open the fob, first locate the notch. Because the notch may not be visible, this is the most difficult aspect. Step 2: Pop it open with the screwdriver. Step 3: Determine the kind of battery. Replace the old battery with a new one in Step 4. Step 5: Secure the fob.

What battery does a 2015 Jeep Grand Cherokee key fob take?

The 2015 Jeep Grand Cherokee key fob battery is Cr2032, which is around the size of a nickle.

What kind of battery does a 2014 Jeep Grand Cherokee key fob take?

Replace the CR2032 battery in the key fob in the same orientation as the previous one (positive side down). The fob’s two parts should snap back together effortlessly. That’s everything! You’re finished!

How do you program a key fob for a 2018 Jeep Grand Cherokee?

Without starting the engine, insert the actual key into the ignition and turn to the first position. Place the key fob programmer in the OBD/DLC port near the pedals beneath the steering column. Press the LOCK and UNLOCK buttons on the key fob at the same time for 3 seconds. For 2 seconds, press the UNLOCK button.

Why does my Jeep say key fob not detected?

The message Key fob not detected’ on your Jeep signifies that a functional key is unable to transmit a transmission to the vehicle, which is often caused by weak batteries in the key fob. Basically, even if the functionality is working properly, this flaw in the key fob stops you from obtaining keyless access to your automobile.

How do you remove a battery from a Jeep Grand Cherokee?

How to Remove the Battery from a Jeep Cherokee Turn the engine off. Pull the hood release clasp inside the car, which is positioned close to the driver’s seat. To release the nuts that hold the wires to the battery terminals, use the wrench. First, loosen the black (negative) one. Then loosen the positive (right) one.

Will AutoZone change my battery?

If you buy a battery from AutoZone, they will install it for free. Instead of charging you a core charge, they will remove your old battery and replace it. They will install the new battery and guarantee that your vehicle starts and operates well once it has been replaced.

Does a 2017 Jeep Grand Cherokee have 2 batteries?

So, wherever you’re going, the Grand Cherokee will make the ride more delightful. The 2017 Jeep Grand Cherokee has two batteries to power all of these fantastic features. The first battery, sometimes known as the main battery, is in charge of cranking the engine and starting the vehicle.

Can you start a 2015 Jeep Cherokee with key?

Registered. Yes, you push the button on the dead fob’s end.

How do you reset the key fob on a Jeep Grand Cherokee?

While the door is still open, turn the knob to the “LOCKposition. In the ignition, turn the key to the “ON” position. On your remote, press and hold the “LOCK” button for five seconds. To test whether you successfully handled Jeep Key fob programming, release the button and remove the key from the ignition.


The “battery for jeep grand cherokee key fob” is a question that has been asked many times on the internet. There are many different battery options and brands to choose from.

This Video Should Help:

The “jeep key fob battery low” is a question that was posted on the Jeep Forum. The answer to the question is found in this article.

Related Tags

  • jeep compass key fob battery
  • jeep key fob battery replacement cost
  • jeep key fob battery
  • 2014 jeep cherokee key fob battery

Similar Posts